| |
Cyberspace 2.4.16 SuSE kernel
18 June 2002
There are two or three instances of dmesg below, run after physically
mounting the new 120GB drive and then again during the LVM definition
process.
A. The physical drive is detected
Linux version 2.4.16-4GB (root@I386.suse.de) (gcc version 2.95.3 20010315
(SuSE))
#1 Mon Apr 15 09:35:46 GMT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ffe000 (usable)
BIOS-e820: 0000000007ffe000 - 0000000008000000 (reserved)
BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
On node 0 totalpages: 32766
zone(0): 4096 pages.
zone(1): 28670 pages.
zone(2): 0 pages.
Building zonelist for node : 0
Kernel command line: auto BOOT_IMAGE=2.4.16 ro root=303 BOOT_FILE=/boot/vmlinuz
enableapic vga=0x0317 SuSE
Initializing CPU#0
Detected 1197.022 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2385.51 BogoMIPS
Memory: 126068k/131064k available (1304k kernel code, 4612k reserved,
388k data, 112k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel(R) Celeron(TM) CPU 1200MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfcaee, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.15)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
vesafb: framebuffer at 0xf1000000, mapped to 0xc880d000, size 16320k
vesafb: mode is 1024x768x16, linelength=2048, pages=8
vesafb: protected mode interface info at c000:02d2
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: QUANTUM FIREBALLP LM10.2, ATA DISK drive
hdb: Maxtor 4G120J6, ATA DISK drive
hdc: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c02fa8a0, I/O limit 4095Mb (mask 0xffffffff)
hda: 19925880 sectors (10202 MB) w/1900KiB Cache, CHS=1240/255/63, UDMA(33)
blk: queue c02fa9c8, I/O limit 4095Mb (mask 0xffffffff)
hdb: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=238216/16/63,
UDMA(33)
hdc: ATAPI 32X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.97.sv
hdd: No disk in drive
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
Partition check:
hda: hda1 hda2 hda3
hdb: unknown partition table
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
loop: loaded (max 8 devices)
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya"
Kasprzak.
ide-floppy driver 0.97.sv
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Uncompressing................................................done.
Freeing initrd memory: 439k freed
VFS: Mounted root (ext2 filesystem).
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=2
Trying to unmount old root ... okay
Freeing unused kernel memory: 112k freed
Adding Swap: 514072k swap-space (priority 42)
ip_tables: (c)2000 Netfilter core team
ip_conntrack (1023 buckets, 8184 max)
Intel(R) PRO/100 Fast Ethernet Adapter - Loadable driver, ver 1.6.29
Copyright (c) 2001 Intel Corporation
PCI: Found IRQ 11 for device 00:0e.0
eth0: Intel(R) PRO/100+ Management Adapter
Mem:0xf4000000 IRQ:11 Speed:100 Mbps Dx:Full
Hardware receive checksums disabled
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 11 for device 00:07.2
uhci.c: USB UHCI at I/O 0xdce0, IRQ 11
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
isapnp: Scanning for PnP cards...
isapnp: Card 'CS4236B'
isapnp: 1 Plug & Play card detected total
snd: unable to grab IRQ 0 for CS4236+ - MPU401
snd: warning: cannot allocate IRQ for MPU401, midi port is disabled
eth0: no IPv6 routers present
B. The LVM module is loaded
Linux version 2.4.16-4GB (root@I386.suse.de) (gcc version 2.95.3 20010315
(SuSE))
#1 Mon Apr 15 09:35:46 GMT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ffe000 (usable)
BIOS-e820: 0000000007ffe000 - 0000000008000000 (reserved)
BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
On node 0 totalpages: 32766
zone(0): 4096 pages.
zone(1): 28670 pages.
zone(2): 0 pages.
Building zonelist for node : 0
Kernel command line: auto BOOT_IMAGE=2.4.16 ro root=303 BOOT_FILE=/boot/vmlinuz
enableapic vga=0x0317 SuSE
Initializing CPU#0
Detected 1197.015 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2385.51 BogoMIPS
Memory: 126068k/131064k available (1304k kernel code, 4612k reserved,
388k data,
112k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel(R) Celeron(TM) CPU 1200MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfcaee, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.15)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
vesafb: framebuffer at 0xf1000000, mapped to 0xc880d000, size 16320k
vesafb: mode is 1024x768x16, linelength=2048, pages=8
vesafb: protected mode interface info at c000:02d2
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: QUANTUM FIREBALLP LM10.2, ATA DISK drive
hdb: Maxtor 4G120J6, ATA DISK drive
hdc: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c02fa8a0, I/O limit 4095Mb (mask 0xffffffff)
hda: 19925880 sectors (10202 MB) w/1900KiB Cache, CHS=1240/255/63, UDMA(33)
blk: queue c02fa9c8, I/O limit 4095Mb (mask 0xffffffff)
hdb: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=238216/16/63,
UDMA(33)
hdc: ATAPI 32X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.97.sv
hdd: No disk in drive
hdd: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
Partition check:
hda: hda1 hda2 hda3
hdb: hdb1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
loop: loaded (max 8 devices)
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya"
Kasprzak.
ide-floppy driver 0.97.sv
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Uncompressing................................................done.
Freeing initrd memory: 439k freed
VFS: Mounted root (ext2 filesystem).
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=2
Trying to unmount old root ... okay
Freeing unused kernel memory: 112k freed
LVM version 1.0.1-rc4(03/10/2001) module loaded
Adding Swap: 514072k swap-space (priority 42)
ip_tables: (c)2000 Netfilter core team
ip_conntrack (1023 buckets, 8184 max)
Intel(R) PRO/100 Fast Ethernet Adapter - Loadable driver, ver 1.6.29
Copyright (c) 2001 Intel Corporation
PCI: Found IRQ 11 for device 00:0e.0
eth0: Intel(R) PRO/100+ Management Adapter
Mem:0xf4000000 IRQ:11 Speed:100 Mbps Dx:Full
Hardware receive checksums disabled
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 11 for device 00:07.2
uhci.c: USB UHCI at I/O 0xdce0, IRQ 11
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
isapnp: Scanning for PnP cards...
isapnp: Card 'CS4236B'
isapnp: 1 Plug & Play card detected total
snd: unable to grab IRQ 0 for CS4236+ - MPU401
snd: warning: cannot allocate IRQ for MPU401, midi port is disabled
eth0: no IPv6 routers present
c. LVM is working -- from /var/log/boot.msg
Run file system check on root for LVM activation
doneRemounting root file system (/) read/write for vgscan...
Scanning for LVM volume groups...
vgscan -- reading all physical volumes (this may take a while...)
vgscan -- found inactive volume group "sys"
vgscan -- "/etc/lvmtab" and "/etc/lvmtab.d" successfully
created
vgscan -- WARNING: This program does not do a VGDA backup of your volume
group
Activating LVM volume groups...
vgchange -- volume group "sys" successfully activated
Activating swap-devices in /etc/fstab...
doneChecking file systems...
fsck 1.24a (02-Sep-2001)
/dev/hda3: clean, 150563/1179648 files, 1090869/2357538 blocks
/dev/sys/vc: clean, 11/15007744 files, 470964/30013440 blocks
/dev/hda1: clean, 35/4016 files, 5161/16033 blocks
doneMounting local file systems...
|
|
